The influence of the length of building net on the solder joint. On the displacement test curve, the peeling force between the coating and the sieve is different: the grid distance is increased, that is, the sample becomes longer. The separation process becomes more and more blurred and less important on the curve.

　　但是，從該曲線可知，隨著網眼間距的增加，測得的實驗力值越來越大，但鍍鋅層與網眼之間的拉力仍為100N左右，變化不大， 目距較小樣品鍍鋅層的剝離力非常明顯，可以簡單觀察到。

　　However, with the increase of mesh spacing, the measured experimental force increases, but the tension between the galvanized layer and the mesh is still about 100N, which has little change. The peeling force of the galvanized layer of the sample with smaller mesh spacing is very obvious and can be easily observed.

　　可以看出，隨著網孔距離的增加，焊點的抗拉強度也逐漸增加。  8倍網格距離大于以1毫米/分鐘表示的4倍網格距離的采樣距離。  52N時，力值以1mm / min大于5倍網眼距離樣品的18N，這表明樣品越長，形成的焊點抗拉強度的正值就越大，規范的規則是 盡可能選擇。 長度，這是在檢查工作中應注意的問題。

　　It can be seen that with the increase of mesh distance, the tensile strength of the solder joint increases gradually. 8 times the grid distance is greater than the sampling distance of 4 times the grid distance expressed in 1 mm/min. At 52N, the force value is greater than 18N of the sample with a mesh distance of 1 mm/min greater than 5 times. This indicates that the longer the sample is, the greater the positive value of the tensile strength of the solder joints formed. The rule of the specification is to select as much as possible. Length, which should be paid attention to in the inspection work.

　　鍍鋅層焊點的抗拉強度值在曲線上反映為較大的實驗力值。 該值是在工程驗收測試中測得的焊點拉伸值； 鍍鋅層的剝離力在曲線上很顯著。 力值在90到100N之間；  （3對“ J”型夾具可用于鍍鋅電焊網在電子測試機上的固定問題，對于避免損壞焊點非常有用。

　　The tensile strength of galvanized solder joints is reflected as a larger experimental force on the curve. This value is the tensile value of solder joints measured in engineering acceptance test, and the peeling force of galvanized coating is remarkable on the curve. The force value is between 90 and 100N; (3 pairs of "J" fixtures can be used to solve the fixing problem of galvanized welding net on electronic testing machine, which is very useful for avoiding damage to solder joints.

　　該建筑網具有保溫，隔音，抗震，防水，施工簡單，重量輕等特點，擴大了建筑的使用范圍，大大降低了工程造價。 施工網的長度一般尺度為：1m * 2m2m * 4m大于6m，否則不好生產。

　　The building network has the characteristics of heat preservation, sound insulation, seismic resistance, waterproof, simple construction and light weight, which enlarges the use scope of the building and greatly reduces the cost of the project. The length of construction network is generally 1 m * 2 m * 4 m larger than 6 m, otherwise it is not good for production.

　　以上是關于鋼筋的構建，希望對大家有所幫助。

　　The above is about the construction of reinforcing steel bar. I hope it will be helpful to you.